Products
منزل > مركز المنتج > Heavy Duty PE Tarpaulin > Blue and Orange PE Tarpaulin, Custom Size, Weight and Thickness

Blue and Orange PE Tarpaulin, Custom Size, Weight and Thickness

Blue and Orange PE Tarpaulin, Custom Size, Weight and Thickness

    Blue and Orange PE Tarpaulin, Custom Size, Weight and Thickness

    Blue outside, orange-red inside: a reversible PE tarpaulin with a heat-welded hem, a rope in all four edges, black triangular corner patches and galvanised eyelets at 1 m. Made to your size, weight and thickness.
  • يشارك:
  • اتصل بنا تحقيق
  • صندوق البريد:961336486@qq.com

Blue and Orange PE tarpaulin, Cut and Welded to Your Size

Blue on the outside with an orange-red inner face. The blue reads calm and industrial on site; the orange lining is easy to see when the sheet is opened out or rigged as a canopy, which helps when the same cover is used and re-used by different crews.

The sheet is woven PE with a continuous coating on both faces, and the edge is folded over and heat-welded rather than stitched, with a rope run inside the fold on all four sides.

Construction

Heat-welded hem, no stitching

The edge is folded over and welded at high temperature, so the coating fuses into one continuous band. There is no row of needle holes along the border — the place a stitched tarpaulin usually starts to leak — and the edge cannot fray.

Rope inside all four edges

A rope runs inside the folded hem on every side, long edges and short. It shares the pull between eyelets instead of letting each fixing point take the load on its own, which is what keeps a sheet from tearing out at the corners in wind.

Reinforced corners

Each corner is covered by a black triangular patch welded over the hem, and the corner eyelet is set through the patch. On sheets from 6 m² upwards the heavier patch is fitted as standard.

Galvanised eyelets

Galvanised eyelets with an 11.25 mm bore are set 1 m apart along the edge, and can be set down to about 30 cm apart where a sheet has to be tied down hard.

Blue and orange PE tarpaulin detail
Detail: welded hem with the rope inside, black triangular corner patch over the blue face and the orange reverse behind.

Specifications

MaterialPE — woven scrim with a continuous coating on both faces
ColourBlue outside, orange-red inside
EdgeFolded over and heat-welded (hot-air), no stitching
ReinforcementRope inside the hem on all four edges
CornersBlack triangular patch welded at each corner, with eyelet
EyeletsGalvanised, 11.25 mm bore, 1 m apart as standard — 30 cm on request
SizeMade to your width × length
WeightMade to your g/m² requirement
ThicknessMade to your requirement
PackingFolded and wrapped for export

Blue and orange PE tarpaulin rigged as a sun canopy
In use: blue and orange PE tarpaulin rigged as a canopy, the orange lining visible from below.

Where It Is Used

Yard and farm storage

Over timber, feed, fertiliser and machinery: the welded hem and the rope inside it spread the load along the edge, so the sheet can be pulled tight and lashed down without tearing at the eyelets.

Transport and equipment covers

On trucks, trailers and boats where a stitched hem would chafe and leak. The smooth welded edge does not fray, and the corner patches take the strain of the tie-downs.

Temporary shelters and canopies

Rigged between posts as a rain or sun cover. Because the size is made to order, one sheet can span an opening without a join down the middle.

Common Questions

What sizes can you make?

Any width and any length, cut and welded to your measurement rather than rounded to a stock size. Send the finished size you need and we quote by area.

Can the weight and thickness be customised?

Yes. Both the weight per square metre and the film thickness are set during production, so the same construction can be supplied as a light cover or as a heavy sheet. Heavier material resists wind load and abrasion better; lighter material is easier to handle and cheaper to ship.

How far apart are the eyelets?

One metre apart as standard, and they can be set closer — down to about 30 cm — where a sheet has to be tied down tightly. The eyelet bore is 11.25 mm.

How is the edge finished?

The edge is folded over and heat-welded at high temperature, then a rope is run inside the fold along all four sides. There are no needle holes, which is the point: a stitched hem puts a line of holes through the coating that water eventually finds.

Are the corners reinforced?

Each corner carries a black triangular patch welded over the hem, with the corner eyelet set through it. On sheets of 6 m² and above the corners are upgraded to the thicker patch as standard.

Is it fully waterproof?

The sheet is a woven PE core with a continuous coating on both faces, so water runs off rather than soaking through, and the welded hems stay sealed. Water can still collect in a slack area, so pitch the sheet so it drains.

Request a Quotation

Send the finished size (width × length), the colour, the weight per square metre or thickness you need, the eyelet spacing and the destination port. We will confirm the price, the welding layout and the production schedule, and can send a material sample and a corner sample before a bulk order.

العلامات ذات الصلة: tarpaulin PE tarpaulin two-colour-tarpaulin

رسالة عبر الإنترنت

الرجاء إدخال عنوان بريد إلكتروني صالح
رمز التحقق لا يمكن أن يكون فارغا

المنتجات ذات الصلة

Binzhou · Shandong · China

Binzhou Taituo Import and Export Co., Ltd

Contact Us

Add: Binzhou, Shandong, China
Tel: +86 19954368176
E-mail: 961336486@qq.com

Copyright © 2026 Binzhou Taituo Import and Export Co., Ltd.

خريطة الموقع
chat

×

يستخدم هذا الموقع ملفات تعريف الارتباط لضمان حصولك على أفضل تجربة على موقعنا.

يقبل يرفض