Products
منزل > مركز المنتج > Heavy Duty PE Tarpaulin > Silver PE Tarpaulin, Custom Size, Weight and Thickness

Silver PE Tarpaulin, Custom Size, Weight and Thickness

Silver PE Tarpaulin, Custom Size, Weight and Thickness

    Silver PE Tarpaulin, Custom Size, Weight and Thickness

    Metallic silver-grey PE tarpaulin with a heat-welded hem, a rope inside all four edges, reinforced corners and galvanised eyelets at 1 m. Size, weight and thickness made to order.
  • يشارك:
  • اتصل بنا تحقيق
  • صندوق البريد:961336486@qq.com

Silver PE tarpaulin, Cut and Welded to Your Size

Silver on both faces: a metallic grey sheet with a bright sheen. It is the usual choice where a cover has to look tidy in front of customers, and a reflective face turns away more of the sunlight that falls on it than a dark sheet does.

The sheet is woven PE with a continuous coating on both faces, and the edge is folded over and heat-welded rather than stitched, with a rope run inside the fold on all four sides.

Construction

Heat-welded hem, no stitching

The edge is folded over and welded at high temperature, so the coating fuses into one continuous band. There is no row of needle holes along the border — the place a stitched tarpaulin usually starts to leak — and the edge cannot fray.

Rope inside all four edges

A rope runs inside the folded hem on every side, long edges and short. It shares the pull between eyelets instead of letting each fixing point take the load on its own, which is what keeps a sheet from tearing out at the corners in wind.

Reinforced corners

Each corner is covered by a black triangular patch welded over the hem, and the corner eyelet is set through the patch. On sheets from 6 m² upwards the heavier patch is fitted as standard.

Galvanised eyelets

Galvanised eyelets with an 11.25 mm bore are set 1 m apart along the edge, and can be set down to about 30 cm apart where a sheet has to be tied down hard.

Silver PE tarpaulin detail
Detail: galvanised eyelets set through the welded hem, black triangular corner patch, coated woven surface.

Specifications

MaterialPE — woven scrim with a continuous coating on both faces
ColourMetallic silver-grey on both faces
EdgeFolded over and heat-welded (hot-air), no stitching
ReinforcementRope inside the hem on all four edges
CornersBlack triangular patch welded at each corner, with eyelet
EyeletsGalvanised, 11.25 mm bore, 1 m apart as standard — 30 cm on request
SizeMade to your width × length
WeightMade to your g/m² requirement
ThicknessMade to your requirement
PackingFolded and wrapped for export

Silver PE tarpaulin over palletised goods
In use: silver PE tarpaulin over palletised goods in an open yard.

Where It Is Used

Yard and farm storage

Over timber, feed, fertiliser and machinery: the welded hem and the rope inside it spread the load along the edge, so the sheet can be pulled tight and lashed down without tearing at the eyelets.

Transport and equipment covers

On trucks, trailers and boats where a stitched hem would chafe and leak. The smooth welded edge does not fray, and the corner patches take the strain of the tie-downs.

Temporary shelters and canopies

Rigged between posts as a rain or sun cover. Because the size is made to order, one sheet can span an opening without a join down the middle.

Common Questions

What sizes can you make?

Any width and any length, cut and welded to your measurement rather than rounded to a stock size. Send the finished size you need and we quote by area.

Can the weight and thickness be customised?

Yes. Both the weight per square metre and the film thickness are set during production, so the same construction can be supplied as a light cover or as a heavy sheet. Heavier material resists wind load and abrasion better; lighter material is easier to handle and cheaper to ship.

How far apart are the eyelets?

One metre apart as standard, and they can be set closer — down to about 30 cm — where a sheet has to be tied down tightly. The eyelet bore is 11.25 mm.

How is the edge finished?

The edge is folded over and heat-welded at high temperature, then a rope is run inside the fold along all four sides. There are no needle holes, which is the point: a stitched hem puts a line of holes through the coating that water eventually finds.

Are the corners reinforced?

Each corner carries a black triangular patch welded over the hem, with the corner eyelet set through it. On sheets of 6 m² and above the corners are upgraded to the thicker patch as standard.

Is it fully waterproof?

The sheet is a woven PE core with a continuous coating on both faces, so water runs off rather than soaking through, and the welded hems stay sealed. Water can still collect in a slack area, so pitch the sheet so it drains.

Request a Quotation

Send the finished size (width × length), the colour, the weight per square metre or thickness you need, the eyelet spacing and the destination port. We will confirm the price, the welding layout and the production schedule, and can send a material sample and a corner sample before a bulk order.

العلامات ذات الصلة: PE tarpaulin scaffolding-sheet silver-tarpaulin

رسالة عبر الإنترنت

الرجاء إدخال عنوان بريد إلكتروني صالح
رمز التحقق لا يمكن أن يكون فارغا

المنتجات ذات الصلة

Binzhou · Shandong · China

Binzhou Taituo Import and Export Co., Ltd

Contact Us

Add: Binzhou, Shandong, China
Tel: +86 19954368176
E-mail: 961336486@qq.com

Copyright © 2026 Binzhou Taituo Import and Export Co., Ltd.

خريطة الموقع
chat

×

يستخدم هذا الموقع ملفات تعريف الارتباط لضمان حصولك على أفضل تجربة على موقعنا.

يقبل يرفض